Switch anvil volume guide from fdisk to parted

content/guides/anvil/formatting_and_mounting_a_volume_in_linux.md

@@ -11,7 +11,7 @@ when it was created, and that you are connected to the [Anvil VPN]({{< relref "
 Once you have [created and attached]({{< relref "creating_and_attaching_a_volume" >}})
 your volume, it must be formatted and mounted in your Linux instance to be usable.  This
 procedure is identical to what would be done when attaching a second
-hard drive to a physical machine.  In this example, a 10GB volume was
+hard drive to a physical machine.  In this example, a 1GB volume was
 created and attached to the instance.  Note that the majority of this
 guide is for a newly created volume.  
 
@@ -32,55 +32,36 @@ command `sudo su -` to get a root shell.
 
 {{% panel theme="danger" header="**Running commands as root**" %}}**Extreme care should be taken when running commands as `root.`** It is very easy to permanently delete data or cause irreparable damage to your instance.{{% /panel %}}
 
-{{< figure src="/images/13599376.png" width="700" >}}
+{{< figure src="/images/anvil-volumes/1-sudo.png" width="576" >}}
 
 Next, you will need to determine what device the volume is presented as
 within Linux.  Typically this will be `/dev/vdb`, but it is necessary to
 verify this to avoid mistakes, especially if you have more than one
-volume attached to an instance.  The command `fdisk -l` will list the
-hard drive devices.  
+volume attached to an instance.  The command `lsblk` will list the
+hard drive devices and partitions.
 
-{{< figure src="/images/13599470.png" width="700" >}}
+{{< figure src="/images//anvil-volumes/2-lsblk.png" width="576" >}}
 
 Here there is a completely empty (no partitions) disk device matching
-the 10GB size of the volume, so `/dev/vdb` is the correct device.
-The `fdisk` utility will first be used to create a single partition.
-Run the command `fdisk /dev/vdb` to start the program using the volume
-disk device.
+the 1GB size of the volume, so `/dev/vdb` is the correct device.
+The `parted` utility will first be used to label the device and then create a partition.
 
-{{< figure src="/images/13599477.png" width="700" >}}
-
-Press `n` for new partition and hit enter.
-
-{{< figure src="/images/13599479.png" width="700" >}}
-
-Press `p` for primary partition and hit enter.
-
-{{< figure src="/images/13599482.png" width="700" >}}
-
-Enter `1` for the partition number.
-
-{{< figure src="/images/13599528.png" width="700" >}}
-
-At the next two prompts hit enter to accept the defaults and return to
-the main command prompt.
-
-{{< figure src="/images/13599530.png" width="700" >}}
-
-Finally, press `w` followed by return to save the changes and
-exit `fdisk`.
+{{< highlight bash >}}
+parted /dev/vdb mklabel gpt
+parted /dev/vdb mkpart primary 0% 100%
+{{< /highlight >}}
 
-{{< figure src="/images/13599533.png" width="700" >}}
+{{< figure src="/images/anvil-volumes/3-mkpart.png" width="576" >}}
 
 Now that a partition has been created, it can be formatted.  Here, the
-EXT4 filesystem will be used.  This is the default filesystem used by
+ext4 filesystem will be used.  This is the default filesystem used by
 many Linux distributions including CentOS and Ubuntu, and is a good
 general choice.  An alternate filesystem may be used by running a
-different format command.  To format the partition using EXT4, run the
+different format command.  To format the partition using ext4, run the
 command `mkfs.ext4 /dev/vdb1`.  You will see a progress message and then
 be returned to the shell prompt.
 
-{{< figure src="/images/13599540.png" width="700" >}}
+{{< figure src="/images/anvil-volumes/4-mkfs.png" width="576" >}}
 
 #### Mounting the volume
 
@@ -96,14 +77,14 @@ following commands to make the directory and mount the volume:
 
 {{< highlight bash >}}
 mkdir /mnt/myvolume
-mnt /dev/vdb1 /mnt/myvolume
+mount /dev/vdb1 /mnt/myvolume
 {{< /highlight >}}
 
-{{< figure src="/images/13599546.png" width="700" >}}
+{{< figure src="/images/anvil-volumes/5-mount.png" width="576" >}}
 
 Running the command `df -h` should then show the new mounted empty
 volume.  
 
-{{< figure src="/images/13599549.png" width="700" >}}
+{{< figure src="/images/anvil-volumes/6-df.png" width="576" >}}
 
 The volume can now be used.